H. van Halewijn, J. Beek
Physixfactor, Nijmegen, The Netherlands
NXP, Eindhoven, The Netherlands
It is important in designing micro-electromechanical systems (MEMS) to reduce the variability of design parameters caused by manufacturing tolerances and material properties. At NXP COMSOL has been used to investigate many aspects of the design, such as the Q-factor, anchor losses, thermal behavior, parasitic capacitance of the resonator and more. Quartz crystal resonators are used in many ...
S.F. Neves, J.J.B.L.M. Campos, T.S. Mayor
CEFT – Transport Phenomena Research Center, Chemical Engineering Department, Porto University, Porto, Portugal
CeNTI - Centre for Nanotechology and Smart Materials, Rua Fernando Mesquita, Vila Nova de Famalicão, Portugal
A clothing system should offer the user a period of relatively comfort. However, changes in the ambient conditions over day affect the heat and mass transport in the system, influencing the user comfort perception. In order to gather information to allow the optimization of clothing systems, it is essential to understand the heat and moisture transfer occurring across multi-layer textiles. For ...
K. Alhazza, B. Albusairi, H. Kamal, H.M.S. Lababiedi, A.A. Abbas
Kuwait University, Kuwait City, Kuwait
Petrochemical Industries Company, Kuwait City, Kuwait
COMSOL Multiphysics has been used to validate and check the design of a header transporting ammonia gases released from pressure safety valves (PSVs) to the tip of the flare. The header is part of a dedicated flaring system to contain emissions from ammonia storage tanks. The two main challenges are the low relief pressure and high capacity of the system. Another difficulty is the high relief ...
Investigation of the Effect of Spinal Defects on Spondylolysis and Stress Fracture of Vertebral Bodies
M.S. Yeoman, C. Quah, A. Cizinauskas, K. Cooper, D. McNally, B. Boszczyk
Continuum Blue, Tredomen, Ystrad Mynach, United Kingdom
The Centre for Spinal Studies and Surgery, Queen’s Medical Centre, Nottingham, United Kingdom
Bioengineering Research Group, Faculty of Engineering, The University of Nottingham, Nottingham, United Kingdom
Spondylolysis (SL) is a defect of the spinal vertebra, and is typically caused by stress fracture of the pars interarticularis bone of the vertebral arch. It is especially common in adolescents who over train in sporting activities. Spina bifida occulta (SBO) is a malformation of the spine where the protruding vertebral bodies are not fully formed. In this study we demonstrate the predisposition ...
P. Trinchero, J. Molinero, G. Román-Ross, A. Nardi, L.M. De Vries, T. Karvonen, P. Pitkänen
Amphos 21, Barcelona, Spain
WaterHope, Helsinki, Finland
Posiva, Eurajoki, Finland
In this work, we present a number of scoping calculations that have been carried out to design an in-situ redox experiment (Figure 1) focused on assessing potential changes in the pH and redox conditions and in the buffering capacity of the Olkiluoto bedrock (i.e. the site for the Finnish spent fuel repository). A characteristic of these models lies in the need to integrate prior information, ...
S. Jordana, A. Nardi
Amphos 21, Barcelona, Spain
Most of mining works, either on the surface or in the underground, demand continuous groundwater pumping in order to operate under dry conditions. When the mining activity stops, dewatering also stops and mining facilities begin to flood, quite quickly at the beginning but becoming slower as the water level in the pit lake rises. The rise of the surface of the lake decelerates due to the bigger ...
Research Center for Power Engineering Problems, KSC, RAS, Russia
Non-Newtonian laminar flows in curved circular tubes with inserts are investigated by computer simulations. 0.65% solution of NaCMC is considered. Three-dimensional incompressible Navier-Stokes equations are solved using COMSOL Multiphysics. Placements of inserts inside the curved tubes and their effects on the hydrodynamics of the flow are studied. Computations are carried out with various ...
C. Tonry, M. K. Patel, C. Bailey, M. P.Y. Desmuliez, W. Yu
Computational Mechanics and Reliability Group (CMRG), School of Computing and Mathematical Sciences, University of Greenwich, London, United Kingdom
Microsystems Engineering Centre (MISCEC, School of Engineering & Physical Sciences, Heriot Watt University, Earl Mountbatten Building, Edinburgh, United Kingdom
State Key Laboratory of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, Jilin, China
Electric Field Assisted Capillarity (EFAC) is a novel technique for the fabrication of hollow polymer microstructures. It has advantages over current methods as it is a single step process. Hollow microstructures have many uses in industry from microchannels and microcapsules in BioMEMS to fibre-optical waveguides. It makes use of the dielectric properties of polymers combined with a heavily ...