K. Al-Shurman, H. Naseem
The Institute for Nanoscience & Engineering, University of Arkansas, Fayetteville, AR, USA
Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, USA
Chemical vapor deposition is considered a promising method for synthesis of graphene films on different types of substrate utilizing transition metals such as Ni. However, synthesizing a single-layer graphene and controlling the quality of the graphene CVD film on Ni are very challenging due to the multiplicity of the CVD growth conditions. COMSOL Multiphysics® software is used to investigate ...
J. Hu, R. Jia, K. Wan, X. Xiong
Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT, USA
Mechanical and Industrial Engineering, Northeastern University, Boston, MA, USA
Department of Electrical Engineering, University of Bridgeport, Bridgeport, CT, USA
The dynamic behavior of droplet impingement on a solid surface is important to many engineering applications. This paper studied the dynamic behavior of a droplet impinging onto solid dry surfaces with different surface wettability using the COMSOL Multiphysics® software. The simulation results were validated against experimental results. It was found that the Level Set method can predict the ...
COMSOL Multiphysics® Software and PV: A Unified Platform for Numerical Simulation of Solar Cells and Modules
M. Nardone ,
 Bowling Green State University, Bowling Green, OH, USA
Introduction: Existing solar cell (photovoltaic, PV) device simulation software is either open source with limited capabilities (1D only) [1,2] or extremely expensive with obscure functionality . PV researchers need an accessible and versatile simulation tool to optimize existing technologies and to reduce the time from concept to prototype for new technologies. This work demonstrates how ...
Simulation of the Temperature Profile During Welding with COMSOL Multiphysics® Software Using Rosenthal's Approach - new
A. Lecoanet, D. G. Ivey, H. Henein
Department of Chemical & Materials Engineering, University of Alberta, Edmonton, AB, Canada
A 3D finite element analysis is carried out, using COMSOL® software, to reproduce the thermal profile obtained with Rosenthal’s equation. The implemented heat transfer equation has been modified as a means to approximate Rosenthal’s solution. An analysis of the differences between the simulation and Rosenthal’s solution, when the geometry of the domain and the source are changed, has been ...
E. Licon, S. Casas, A. Alcaraz, J.L. Cortina, C. Valderrama
Universitat Politécnica de Catalunya, Barcelona, Spain
Ammonia separation from water by membrane contactor was simulated on transient state and compared with experimental data. Aqueous low concentrated solution of ammonium with high pH has been pumped inside the hydrophobic hollow fibers, acid solution in the outside part. The system is in closed loop configuration. In order to simulate the separation process, equations were developed considering ...
G. Madabattula, S. K. Gupta
Department of Chemical Engineering, Indian Institute of Science, Bangalore, Karnataka, India
Low cost high energy density batteries that can be charged and discharged rapidly are required in a number of applications. Tapping energy from renewal resources such as solar, wind and tide requires rapidly generated energy to be first stored and then used round the clock. Storing energy of a moving vehicle as it slows down and recovering it to accelerate the vehicle later can significantly ...
S. Kumar, and M. Raju
General Motors R&D Center, Warren, MI, USA
Optimal CAE Inc., Detroit, MI, USA
Hydrogen refueling in a metal hydride based automotive hydrogen storage system is an exothermic reaction and hence an efficient heat exchanger is required to remove the heat for fast refueling. In this paper a helical coil heat exchanger embedded in a sodium alanate bed is modeled using COMSOL. Sodium alanate is present in the shell and the coolant flows through the helical tube. A three ...
A Flow and Transport Model in Porous Media for Microbial Enhanced Oil Recovery Studies Using COMSOL Multiphysics® Software
M. A. Diaz-Viera , A. Ortiz-Tapia ,
 Mexican Petroleum Institute, Mexico City, Mexico
A flow and transport model in porous media was implemented in COMSOL Multiphysics® software to simulate, analyze and interpret Microbial Enhanced Oil Recovery (MEOR) processes at core scale under laboratory conditions. The flow model is biphasic and is based on the oil phase pressure and total velocity formulation in which the capillary pressure, relative permeabilities, the effects of ...
A. Bahrami, D. K. Aidun
MAE Department, Clarkson University, Potsdam, NY, USA
COMSOL Multiphysics® is used to simulate the transport phenomena in arc welding of Nickel to 304SS. Electric Currents (ec) and Magnetic Fields (mf) are used to solve for the Lorentz force which is one of the volume forces. Laminar Flow (spf) is used to simulate flow field. The Lorentz and buoyancy forces are applied as volume forces to the fluid domain. Marangoni effect also is applied to the ...
D. Groulx, and W. Ogoh
Mechanical Engineering Department, Dalhousie University, Halifax, Nova Scotia, Canada
One way of storing thermal energy is through the use of latent heat energy storage systems. One such system, composed of a cylindrical container filled with paraffin wax, through which a copper pipe carrying hot water is inserted, is presented in this paper. It is shown that the physical processes encountered in the flow of water, the heat transfer by conduction and convection, and the phase ...