O. Vogel, and J. Ulm
Proportional solenoids are well-known and used in a wide range of applications today. This paper is about methods of influencing the characteristic force-stroke-curves of magnetic actuators by means of different pole geometries. The conical design of the stator pole which is mostly used to accomplish proportional solenoids is analyzed by both a simple analytic reluctance model and a FEM model ...
Lamb Waves and Dispersion Curves in Plates and It’s Applications in NDE Experiences Using Comsol Multiphysics
P. Gómez, J. P. Fernandez, and P. D. García
Hydro-Geophysics & NDE Modeling Unit
University of Oviedo
In this paper, a model for numerically obtaining lamb wave modes and dispersion curves in plates is presented. It is shown that COMSOL Multiphysics can be employed to simulate the behavior of guided waves in dispersive plates, which is useful for NDE applications. A two dimensional steel plate (4x0.1 meters) is excited with a space-time impact point source. To model the point source, we use ...
J. L. Munoz, and I. Rodriguez
A proton linac drives particles using the electric field of a high power RF standing wave in a resonant cavity. The design of these cavities involve several aspects of multiphysics simulation, that have been accomplished using COMSOL. The first step consist on the geometric optimization of the cavities in order to have the correct frequency while maximizing some figures of merit. This task ...
I. Avram, and I. Gavril Tarnovan
The Technical University of Cluj Napoca
This paper presents a study on the propagation modes of electromagnetic waves through a step index fiber optics. To analyze the propagation of electromagnetic field, a simulation in Comsol 4.0 has been implemented using two different optical fibers. Obtaining the propagation modes, called linearly polarized modes (LPnm) to get their characterization according to the radial and azimuthal ...
L. Spicci, and M. Cati
The present paper describes the development of a full FEM model for linear array high performance 5MHz ultrasound imaging transducer. As a preliminary design, a mono dimensional electro-acoustical KLM model was realized, then the complete FEM was developed and optimized. The optimized transducer was manufactured, so that agreement between transducer measured performances and simulation ...
J. Förster, and H. Vogt
Institute of Electronic Components and Circuits
A one-dimensional model of Excimer Laser-Annealing of amorphous silicon layers which are irradiated with a KrF excimer laser is described. For realisation, the application mode heat transfer in solids is used. The model predicts a melt threshold for the energy density of the laser of 88.5 mJ/cm^2. It also predicts a linear increase of the melt duration with a slope of approximately 625 (ns*cm^2) ...
Analytical and Experimental Validation of Electromagnetic Simulations Using COMSOL®, re Inductance, Induction Heating and Magnetic Fields
M. W. Kennedy, S. Akhtar, J. A. Bakken, and R. E. Aune
Norwegian University of Science and Technology (NTNU)
This paper presents a snap shot of experimental work, which has been conducted at NTNU on billet heating with induction coils. A significant volume of experimental data have been collected for coils running with up to 0.2T: high accuracy Hall probe readings (+/-1%), metal conductivity (+/-0.5%), and heat generation (+/- 4%) have been collected. Results are analyzed using newly developed ...
A.Buchau, and W. M. Rucker
Institut für Theorie der Elektrotechnik
The simulation software COMSOL Multiphysics is applied to the numerical com-putation of the magnetic fields of a three-phase transformer. A three-dimensional model of the geometrical configuration is created with the help of the CAD tools of COMSOL Multiphysics. There, all dimensions of the transformer are defined by parameters. The creation of an optimal finite element mesh is improved by some ...
M. Herlitschke, M. Blasl, and F. Costache
Fraunhofer Institute for Photonic Microsystems
3D FEM simulation of millimeter-scale, complex electro-optically induced waveguide based devices demands the use of grids with more than several million nodes. Hence the simulation could take substantial time and require large amounts of available memory. This paper presents a computation algorithm based on the conversion of an initial 3D waveguide structure into an analogous 2D structure, ...
B. Chinè , and M. Monno
Laboratorio MUSP, Macchine Utensili e Sistemi di Produzione, Piacenza, Italy and Instituto Tecnologico de Costa Rica, Cartago, Costa Rica
Politecnico di Milano, Dipartimento di Meccanica, Milano, Italy
Modeling and simulation softwares are very useful tools when we have to analyse and understand the different phenomena occurring during metal foams processing, because several simultaneous physical mechanisms have to be accounted for. In this work we use Comsol Multiphysics 4.2 to model a spherical hydrogen gas bubble expanding in aluminium liquid, initially at rest. The aim of the present ...