Electrical

Mads Herring Jensen | January 2, 2014

I recently had the pleasure of preparing a small contribution to the 166th Meeting of the Acoustical Society of America (Fall 2013) together with Wade Conklin and Jordan Schultz from Knowles Electronics. Wade presented our paper entitled “Characterization of a microelectromechanical microphone using the finite element method”. The work consisted of implementing a virtual prototype of a Knowles MEMS microphone (the SPU0409LE5H microphone, see picture below) using COMSOL Multiphysics.

Read more ⇢

Article Categories

Alexandra Foley | December 30, 2013

Not too long ago, my colleague Jennifer wrote a blog post about the Cross Cancer Institute, and the research being conducted there into the design of a new device for treating cancerous tumors. The device, known as the Linac-MR, is revolutionary due to its ability to both image and treat cancer cells simultaneously — a capability that had previously been regarded as near impossible due to the conflicting physics interactions involved. Such a device would allow for extremely precise radiation […]

Read more ⇢

Article Categories

Daniel Smith | December 11, 2013

Microwave plasmas, or wave-heated discharges, find applications in many industrial areas such as semiconductor processing, surface treatment, and the abatement of hazardous gases. This blog post describes the theoretical basis of the Microwave Plasma interface available in the Plasma Module.

Read more ⇢

Article Categories

Magnus Olsson | December 2, 2013

When designing inductive devices, both challenges and possibilities are associated with the nonlinear behavior of ferromagnetic materials. COMSOL Multiphysics is well-adapted to the solution of highly nonlinear numerical models but high-fidelity modeling of nonlinear inductive devices also requires accurate material data. To meet this challenge, a library of 165 nonlinear magnetic materials is provided in COMSOL 4.4, bringing new powers to the design and modeling of electric motors, transformers, relays, etc. Here, we will discuss how the modeling process is […]

Read more ⇢

Article Categories

Fanny Littmarck | November 8, 2013

There were many interesting posters at this year’s COMSOL Conference in Boston. A couple that caught my eye involved microwave heating and chemical applications. One of them showcases the use of microwave irradiation to speed up chemical reactions. Another — one of the recipients of the Best Poster award — used simulations to optimize their microreactor design with respect to microwave propagation.

Read more ⇢
Alexandra Foley | October 11, 2013

A Wilkinson power divider is a common three-port power splitter circuit that is used to split an input signal into two equal output signals, or to combine two signals into one. Unlike resistive or T-junction power dividers, a Wilkinson power divider allows for nearly complete isolation between the two ports and adds no resistive losses to the power split. Because of these characteristics, a Wilkinson divider is widely used in radio communication systems due to its ability to prevent crosstalk […]

Read more ⇢

Article Categories

Fanny Littmarck | October 8, 2013

A Gaussian beam that is striking an array of nanorods is an example of optical scattering. Consider metallic nanorods that are very close together and have a diameter much smaller than the wavelength of a Gaussian beam that falls upon them. If the beam were to be polarized along the rods, they would act as though they were not actually individual rods, but a sheet of metal. The array is nearly transparent to the wave when it is polarized perpendicular […]

Read more ⇢

Article Categories

Supratik Datta | September 25, 2013

If you are using a cell phone, GPS, Bluetooth, or WiFi, chances are that they all have BAW resonators working inside them. All wireless electronic equipment use RF filters to help narrow down the frequency range they should operate within. With thousands of devices working within closely-packed radio frequencies, it is becoming increasingly important to design filters that would be able to reduce interference from unwanted frequencies, boost the signal-to-noise ratio, and lower insertion loss. Doing so may lead to […]

Read more ⇢

Article Categories

Walter Frei | September 10, 2013

A question we get asked all of the time is: “Which of the COMSOL products should be used for modeling a particular electromagnetic device or application?” There are currently six modules labeled as “Electrical” in the product suite; the AC/DC Module, RF Module, Wave Optics Module, MEMS Module, Plasma Module, and Semiconductor Module. The first four address applications purely governed by various forms of Maxwell’s equations, while the Plasma Module addresses the coupling of electromagnetic fields to plasma transport and […]

Read more ⇢

Article Categories

Alexandra Foley | September 3, 2013

It’s probably something we have all experienced. We get home, stick last night’s leftovers in the microwave, and sit down to have a nice meal — only to realize that the food is scalding hot one bite and freezing cold the next. This experience has prompted me on more than one occasion to wonder: Why does a microwave heat food so unevenly?

Read more ⇢

Article Categories

Walter Frei | August 30, 2013

Recently, I was given a copy of the book Finite Element Modeling Methods for Photonics, by B.M. Azizur Rahman and Arti Agrawal. This book proved to be a good companion to the RF Module and Wave Optics Module for graduate students starting in photonics and new users of COMSOL who would like a very targeted introduction to the field. The website accompanying the book comes with some sample computer codes used by the authors in simulation that readers can use […]

Read more ⇢

Article Categories

1 2 3 4 7